Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Repair for Kent Homeowners
A garage door that won’t close leaves your home open. One that won’t open traps the car inside. Either way, the day stops until it’s fixed. We handle garage door repair across Kent for exactly those moments, and for the slower problems too: a door that shudders on the way down, a bottom panel bent out of line, a remote that works only when you’re standing close. Our technicians have up to 10 years of experience and work on your brand rather than guessing at it. Same-day and emergency service are available, and pricing is agreed before any work starts. Call (877) 606-8952 and describe what the door is doing. That’s usually enough for us to know what to bring.
What Our Garage Door Repair Service Includes
Most garage door failures fall into a handful of categories, and each one calls for a different set of tools and a different safety approach. Here’s what we handle in Kent, and how you’ll know it’s time.
Panel Replacement
A single damaged panel is the most common cosmetic and structural repair we see. A door that took a hit from a car, a bike handle, or a stray branch rarely needs to be replaced whole; the affected section can be swapped out and the door brought back to square. We match panel profiles and colors across Amarr, Wayne Dalton, and Clopay doors, and we check the surrounding sections for bends that don’t show until the door runs. If the panel is bent enough to bind against the one beside it, replacing it protects the hinges from taking the wear.

Spring Repair
Springs carry the full weight of the door, and they fail loudly: a bang from the garage, and the door stops halfway or won’t lift at all. Torsion and extension springs are the most dangerous component on the whole system, which is why we treat them as a specialty rather than a side job. A trained technician relieves the tension with the right winding bars and measures the replacement against the door’s actual weight. Please don’t attempt this yourself. The stored force in a wound spring can cause serious injury in an instant, and there’s no safe way to work on one without the proper tools and training.

Cable Repair
The cables are what connect the springs’ lift to the door itself, running down each side over the drums. A frayed or snapped cable shows up as a door that hangs crooked, one corner sagging, or a loud pop followed by a door that won’t move evenly. Cables carry the same stored tension as the springs, so they get replaced in matched pairs and inspected alongside the spring system, never repaired with a patch. We check the drums and the bottom brackets at the same time, because a worn drum will chew through a new cable quickly.

Track Realignment
The overhead tracks guide the door through its arc, and a bend of even half an inch throws the whole run off. You’ll hear it as a scrape or a grind, or see the door rub against one side as it travels. Impact damage, a loose bracket, or a house settling on one corner can all knock the track out of true. We straighten and re-anchor the track rather than forcing the door to follow a bent rail, since a misaligned track wears out the rollers and hinges ahead of schedule.
Roller Replacement
Rollers are the small wheels that ride inside the track, and they’re the cheapest part of the system to ignore until they’re the loudest. Steel rollers flatten over time and nylon ones crack with age, both of which make the door rumble, squeal, or jump in the track. Replacing a full set is quick, quiets the door noticeably, and takes strain off the opener. We check roller condition on every repair visit, because a seized roller will shorten the life of the hinges and the track behind it.
Sensor Calibration
The two safety sensors at the bottom of the door frame stop the door from closing on anything in its path, and they cause more “my door won’t close” calls than any other component. A bumped sensor, sun glare, or a loose wire can all break the beam, and the door reverses or refuses to move. We realign the sensors, check the wiring back to the opener, and test the beam at both ends of travel. Kidde-style alignment issues aside, this is often a fifteen-minute fix once the cause is found.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Repair
We work across eight of the most widely installed garage door and opener brands in the country, which means we diagnose the actual make and model rather than guessing at a generic failure. On Amarr doors, we know where the hinge plates and section seams take the most stress on a heavier steel door, and where a bent bottom section typically starts. Wayne Dalton doors have their own balance and hardware quirks, and we’ve learned which of their panel profiles are still available for a match and which call for a different approach. Craftsman openers are everywhere in Kent’s older housing, and we know their limit settings and sensor wiring well enough to skip the guesswork.
Clopay doors, common on newer builds around Fairwood and Covington, have their own panel interchange and window insert systems, so a color match doesn’t have to mean a full door. Raynor systems and their commercial-grade springs come up too, and springs are springs to a trained technician: the wire gauge and the door’s weight determine the replacement, not the label. Opener repair runs across LiftMaster, Chamberlain, Genie, and Craftsman, and brand-specific diagnostics make a real difference on smart openers that throw error codes a generalist won’t recognize. Whether you have Amarr, Wayne Dalton, Craftsman, Raynor, or any other make, we can help.
Signs You Need Garage Door Repair Right Now
A garage door rarely fails without warning. These are the signals worth calling on before something breaks outright.
- A loud bang from the garage followed by a door that won’t lift. That’s the sound of a spring breaking, and the door is now dead weight. Don’t try to force it open with the opener, since the motor will strain against a load it was never designed to carry. Call us and we’ll book spring repair.
- The door closes unevenly or hangs at an angle. One side dropping lower than the other usually points to a stretched or snapped cable, or a spring that’s lost its tension. Running the door in that state grinds the rollers and can bend the track. It needs a look before the next cycle.
- The door reverses or won’t close at all. This is almost always the safety sensors at the base of the frame. It could be a bumped unit, morning sun hitting one sensor, or a wire that’s come loose. A quick check and recalibration usually solves it.
- Grinding, scraping, or squealing during travel. Metal-on-metal noise means a roller or track problem, and it gets worse the longer it runs. Worn rollers are cheap to replace; a worn track or a damaged opener is not. The noise is your early warning.
- The door is visibly bent, dented, or off its track. Impact damage from a car or a storm can knock the door out of the track and leave it hanging. Don’t run the opener if the door is off its rails, since the motor will pull against the jam and cause more damage. That’s a same-day call.
Any of these signs is worth a call to (877) 606-8952. Estimates are free, and we’ll tell you plainly whether it’s a repair or something bigger.
Our Garage Door Repair Process – Step by Step
- 1
You describe the problem and we ask questions. What the door does, when it started, and the make of the door and opener if you know it. That phone conversation often narrows the cause before we arrive, which saves time and helps us bring the right parts.
- 2
We inspect the whole system, not just the broken part. Springs, cables, rollers, hinges, track, and the opener get checked together, because a snapped spring often takes a cable or a roller with it. A door that’s diagnosed in isolation gets fixed twice.
- 3
We give you a written estimate before any work starts. The price is quoted and agreed before a single tool comes out. No surprises at the end, no upsell pressure. If we find something else, we show you and let you decide.
- 4
We do the repair with the right parts for your door. Matched springs for your door’s weight, cables replaced in pairs, panels matched to your existing profile where possible. Brand knowledge matters here, and our technicians have up to 10 years of experience across the major makes.
- 5
We test the full cycle and walk you through it. The door runs up and down, the safety reverse is checked, the sensors are confirmed, and we show you what we did. If anything feels off, we adjust it before we leave. That’s the satisfaction guarantee.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Repair Cost in Kent?
Garage door repair in Kent typically runs $150 – $600, and most single repairs land in the lower half of that. Here’s how the common jobs break down as estimated ranges:
| Repair | Typical Estimated Range |
|---|---|
| Spring Repair (one spring) | $180 – $340 |
| Cable Repair | $130 – $250 |
| Opener Repair | $120 – $320 |
| Panel Replacement | $250 – $500 |
| Track Realignment | $120 – $240 |
| Roller Replacement | $110 – $220 |
| Garage Door Repair (overall) | $150 – $600 |
A spring repair is priced for one spring. Springs are usually replaced as a matched pair, so a pair costs about twice that range. That’s not an upsell; a new spring next to an old one wears unevenly and the door runs out of balance. A typical panel replacement in Kent runs $250 – $500 depending on the panel size and whether the profile and color need to be matched to an older door. Opener repair runs $120 – $320, and sensor calibration or a roller swap sits at the low end of the table.
What moves the price: the door’s weight and size, the parts required, and whether the failure damaged anything alongside it. A snapped cable often means a worn drum, and a bent track often means worn rollers. We quote the whole job up front so you’re not hit with add-ons later. To avoid overpaying, get the estimate in writing, ask what’s included, and be wary of anyone who quotes a price without looking at the door. Our free estimate covers the inspection, the diagnosis, and a written price. The written estimate sets the final price, and the price is quoted and agreed before any work starts. Call (877) 606-8952 for an exact quote.
Garage Door Repair Near Kent – Our Service Area
We cover Kent and the surrounding communities, including Maple Valley, Covington, Fairwood, Des Moines, Auburn, SeaTac, Lakeland North, and Lake Morton-Berrydale. Response times depend on the day and the job, but we aim to reach most of these areas the same day for repair and emergency calls. Port Orchard and Bainbridge Island are covered on the peninsula side, and Snoqualmie on the east. If you’re in one of these towns and your door is down, call and we’ll give you an honest window. Our Kent Garage Door Repair Pros team can also point you to garage door repair and garage door repair resources for those areas.
Serving Kent, WA – Our Local Coverage Area
We serve Kent and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Repair in Kent
Garage door repair is the diagnosis and fixing of any component that stops the door working safely: springs, cables, rollers, hinges, track, panels, and the opener and its sensors. It’s not the same as a new installation, though a badly damaged door sometimes moves that direction. Most repairs are done on the door you already have, and our technicians have up to 10 years of experience diagnosing which part failed and why. Call (877) 606-8952 if you’re unsure whether your problem is a repair or a replacement.
Most single repairs take under two hours, and many take well under one. A roller swap or sensor calibration is quick; a spring or cable replacement takes longer because the tension has to be relieved and reset safely. Panel replacement depends on whether the panel is in hand or needs to be matched and ordered. We’ll give you a time estimate when we book the job, and we don’t leave a door half-finished.
Most garage door repairs in Kent run $150 – $600, and a single spring runs $180 – $340, with a matched pair about twice that. Cable repair is typically $130 – $250, and track realignment $120 – $240. The written estimate sets the final price, and we quote and agree it before any work starts. Call (877) 606-8952 for an exact quote; estimates are free.
Yes. We service Amarr, Wayne Dalton, Craftsman, Raynor, Clopay, LiftMaster, Chamberlain, and Genie equipment, and we diagnose by the actual make and model rather than a generic guess. That matters on panel matching, spring sizing, and opener error codes, where brand-specific knowledge saves time and money. Whether you have one of these or another make, we can help.
Yes, emergency garage door service is available for doors that are stuck open, off their track, or won’t close and leave the house unsecured. A broken door is a safety and security problem, and we treat it that way. Call (877) 606-8952 and describe the situation; we’ll tell you what we can do and when. Pricing is still quoted and agreed before we start.
Yes, our work carries a satisfaction guarantee, and parts carry their own coverage depending on the manufacturer. If something we fixed doesn’t hold, we’ll come back and make it right. Ask us about the specific coverage on your job when we give you the written estimate, so you know exactly what’s covered.
Clear the area in front of the door and under the motor so the technician can work safely, and make sure the door is accessible from the garage side. If you know the make and model of the door and opener, have it handy; if the opener is paired to remotes or a smart hub, note that too. Don’t try to open or close a broken door yourself before we arrive, especially if a spring or cable has failed.
Schedule Your Garage Door Repair Service in Kent Today
A broken door doesn’t get better on its own. Whether it’s a snapped spring, a door off its track, or sensors that won’t let it close, we can help, and same-day and emergency service are available. Call (877) 606-8952 for a free, no-obligation estimate. Pricing is agreed before any work starts, and the written estimate sets the final price. We service Amarr, Wayne Dalton, Craftsman, Raynor, and more. One company, every garage door need.
Written by the team at Kent Garage Door Repair Pros.