Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Kent?
Spring replacement in Kent typically costs $180 to $340 for one spring. When both springs in a matched pair are replaced together, which is what we usually recommend, expect roughly twice that: about $360 to $680. The written estimate we give you after looking at the door sets the final price, and that estimate is free.
Two numbers matter here, and they trip people up. A torsion spring and an extension spring do the same job, but they’re different parts with different labor. And a door with two springs rarely needs only one replaced. If one has snapped, its partner is carrying the full load and is usually at the end of its life too. We’ll show you the condition of both before anything gets ordered.
Key Takeaways
- One spring: $180 – $340. A matched pair: about $360 – $680.
- Most broken-spring calls are resolved with a single visit.
- Cables, rollers, and tracks often get inspected at the same time. Spring replacement is the main job, but a snapped spring can throw a cable off its drum.
- Free estimates. Call (877) 606-8952.
Spring Replacement Cost Breakdown (2026)
These are typical estimated ranges for the Kent market. Your specific door, its weight, and the spring type determine where in the range your job lands.
| Job | Typical Estimated Cost |
|---|---|
| One torsion spring | $180 – $340 |
| Matched pair of springs | About $360 – $680 (roughly double the single-spring range) |
| Extension spring (one) | $180 – $340 |
| Cable repair (often needed with spring work) | $130 – $250 |
| Roller replacement | $110 – $220 |
| Track realignment | $120 – $240 |
| Panel replacement (if a spring failure damaged a section) | $250 – $500 |
| General garage door repair call | $150 – $600 |
What pushes a spring job toward the top of the range? A heavier door: double-wide doors, doors with insulated steel or wood panels, and anything above the standard seven-foot height. Those need a stronger spring, and often a pair rather than a single. Custom or high-lift hardware also adds labor. A straightforward single-spring swap on a standard single-car door sits near the bottom. If your door won’t open at all right now and you’re also hearing a loud bang from the garage, one of our technicians can sort out whether it’s the spring or something else before anything gets ordered.
The estimate you get should be the price you pay. We spell out the parts, the labor, and anything we found during the inspection. No surprise numbers after the door’s back in place.
What Affects Spring Replacement Pricing in Kent
Kent is not one kind of housing stock. The west hill neighborhoods sit close to the Green River Valley and its damp winter air, while the east side climbs toward the plateau where wind and temperature swings hit harder. Both things wear on the hardware that holds a garage door up.
- Door weight and size. A single-car door with a light steel panel needs one spring. A double-car insulated door often needs two. The heavier the door, the stronger and more expensive the spring, and the more labor to swap it safely.
- Torsion vs. extension springs. Torsion springs mount above the door and are the more common setup on newer homes. Extension springs run along the sides on tracks and are typical of older doors. The two systems require different tools and different safety procedures, so the labor differs.
- Spring cycle rating. Springs are rated by cycles, meaning how many open-and-close runs they’ll survive before breaking. A higher-cycle spring costs more up front. On a frequently used door, that’s usually money well spent.
- Condition of the rest of the door. A snapped spring can yank a cable off its drum or bend a track. Cables run $130 – $250 and track realignment $120 – $240, and both may be needed in the same visit.
- Rust and corrosion on the hardware. In the damp parts of the Puget Sound lowlands, the springs, drums, and bearing plates on old doors sometimes corrode enough that the hardware needs work beyond a straight swap. We look at this before quoting.
- Access and setup. A car parked under a dead door needs to be moved first. A cluttered, low-clearance garage ceiling can slow things down. Most jobs are still done in a single visit.
There’s one more variable worth naming. Some older doors were installed with extension springs that lack a safety containment cable running through the spring. If one of those lets go, it can fly. That’s a safety concern, not a pricing detail, but it’s one a technician will flag on arrival. Adding a containment cable is part of bringing an old door up to a safer setup.
How to Save on Spring Replacement
There’s no cheap way around a broken spring, and it’s not a part anyone should ignore. But a few practical moves keep the number reasonable.
- Replace the pair, not just the broken spring. Replacing one spring on a door with two means the second swap comes sooner. Doing both at once usually saves the second visit charge.
- Get other parts inspected during the same visit. If you have a cable or a roller on its last leg, bundle it into the same appointment instead of paying for two separate calls. Cables run $130 – $250 and rollers $110 – $220.
- Ask about the cycle rating. Upgrading to a higher-cycle spring costs more on paper, but it can outlast a standard one by a wide margin on a door you open several times a day.
- Don’t wait for a second spring to snap. A door running on one spring is under uneven load. It works the opener harder and can throw the door off balance. Getting ahead of it usually means one repair instead of two.
- Get a free written estimate. We don’t charge for the visit or the quote. Call (877) 606-8952 and we’ll walk you through how a spring job goes and what it costs for your door.
Don’t try this one yourself
We’ll say it plainly, because it’s the most important thing on this page. A torsion spring stores enormous energy. That energy has to be released safely before the spring comes off, and the spring has to be wound back to the right tension afterward. Doing it without the right tools and training causes serious injuries, and the part gives no warning. Extension springs are less dangerous by comparison, but the old ones can still fly. This is a job for a trained technician. We handle it as a specialty, work on your door’s actual brand and model, and won’t leave anything half-finished.
Nobody should be poking at a wound torsion spring with a screwdriver. If yours has snapped, keep the door closed if you can, away from kids and pets, and get a technician out.
Why The Right Spring Matters For Your Door
A garage door spring isn’t a one-size part. It’s matched to the weight of the door, the size of the drum, and the height of the opening. Put the wrong one on and the door will feel too heavy to lift by hand, the opener will strain, and the spring will wear out faster than it should. That’s why a technician checks the door’s weight and hardware before ordering anything. Brand matters too. We work on LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor systems, so we recognize the common door-and-opener setups by the specific hardware they use.
If you’re comparing repair against replacement, here’s the rough line. Spring replacement runs $180 – $340 per spring. A new door installation runs $700 – $2200. For a door in otherwise good shape, replacing the springs is the cheaper route by a wide margin. If the door has rotted panels, bent tracks, and a worn opener on top of the springs, a new install can start to make sense. We’ll tell you which side of that line your door is on without pushing you toward either one.
When the spring work is done, we test the balance, the opener limits, and the safety reverse, so the door closes properly against the floor. A door that reverses on a light touch is a door that’s set up right.
FAQs – Spring Replacement Cost
How much does it cost to replace a garage door spring in Kent?
One spring typically runs $180 – $340. A matched pair, which is the common recommendation when both springs are the same age, runs about $360 – $680. The written estimate sets the final price. Call (877) 606-8952 for a free quote.
Is it cheaper to repair or replace a garage door spring?
Repair is almost always the cheaper answer at $180 – $340 for one spring. Replacement of the entire door only makes sense when other parts (panels, tracks, opener) are failing at the same time, which brings the job into new-door territory at $700 – $2200. Call (877) 606-8952 and we’ll tell you which side of the line your door sits on.
Can you replace a broken spring the same day?
Same-day spring service is often possible, and most spring calls only need one visit. If one spring has snapped, we aim to have it sorted the same day the technician arrives. Call (877) 606-8952 and we’ll get you on the schedule.
Do I need to replace both springs if only one broke?
Usually, yes. A pair of springs installed together has the same wear, so when one snaps the other has similar hours on it. Replacing both at once typically lands in the $360 – $680 range for the pair and avoids a second visit. Call (877) 606-8952 to talk through your door’s setup.
Why did my garage door spring break in Kent?
Springs break from cycle fatigue, not from a single bad moment. Every open and close is one cycle, and the spring is built for a set number. In Kent’s damp, cool winters the repeated wet-and-dry cycle on older hardware adds to the wear. When the cycle limit arrives, the spring breaks with a bang, usually when the door is closing. That’s why we recommend a higher-cycle spring on a frequently used door. Call (877) 606-8952 for a free estimate.
Diagnose It, Then Fix It Right
If a spring has snapped on your door, the door is heavier than the opener can safely lift. Keeping the door closed and away from traffic is the right move until we can look at it. Our technicians have up to 10 years of experience and handle spring work as a specialty, whether it’s a torsion or extension setup. We work on your brand: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, or Raynor. We also handle opener repair and general garage door repair, so if a bad spring has strained the opener, that’s covered in the same visit. For the broader picture of what we do, start at Kent Garage Door Repair Pros.
Call (877) 606-8952 for a free estimate. We’ll tell you what the job costs in Kent before anyone starts, and we’ll have the hardware checked so the door is back on its tracks and lifting safely the same visit.
Pricing reflects the Kent market as of 2026. Kent Garage Door Repair Pros offers free estimates – call (877) 606-8952.
What Our Customers Say
"Both cables had come off the drum and the door was hanging crooked. I'd watched a video and was about ten minutes from trying it myself, which the tech told me would have been a genuinely bad idea. Glad I called."
- Gabriela Vargas"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Heather Hayes"Fixed the spring properly and the door works fine. He did leave the old spring and some hardware by the side of the house, and I had to text to ask about hauling it off. They came back for it, just took a couple of days."
- Priya Patel